Conveyor body | Idle ends | Drive unit – end drives | Drive unit – high capacity end drives | Drive unit – center drives | Drive end – offset transfer | Drive end – in line transfer | Bends – horizontal bends | Bends – up vertical bends | Bends – down vertical bends
XCT • Closed top sanitary conveyor Table-top chain

Areas of applications
- Applications where line clearance between batches or lot numbers is required.
- Tablet filling lines.
- Powder filling lines.
- Liquid filling lines.
- Plastic and glass container packing lines.
Advantages
- Minimum cleaning time.
- Minimum maintenance.
- Maximum resistance to harsh products and environments.
- Raised chain: allow visual inspection underneath.
Geometry
- The belt rides on top of two raised flat bars (raceway).
- The raceway is attached to the lower inverted “U” stainless steel body by means of spacers.
Unique cleaning advantages
- 1-½” clearance between the raised raceway and the body.
- Stainless steel raceways without crevices.
- End barriers to prevent product entrance to the lower body.
- Minimum horizontal surfaces where debris or product could accumulate.
Unique maintenance advantages
- Sealed bearings, no lubrication necessary.
- No squeaking belt curve guides.
Unique fabrication advantages
- Belt elongation gage.
- Pre-engineered transfer plates and accessories.
- Modular section and accesories.
Unique ergonomic advantages
- Optional: minimum body depth design. Allows operators to place their legs under the conveyor.
Pre-engineered accessories
- See the Ancillary Equipment section.
- Your accessory: give us your requirements, we will custom-design it at affordable prices.
Options
- See the Ancillary Equipment section.
- No-tool return wearstrip removal (on straight sections only).
- Inspection/cleaning windows on the body.
- Swivel end safety guards.
- Discharge end product slide.
- Metal detector, metal free zone.
- Washdown motors, controls and reducers.
- Chain-driven models:
- Torque limiter.
- No-lubrication chain.
- Timing belts.
- See-through chain cover.
Mechanical specifications
- Standard belt type: table-top chain (LF).
- Optional belt types and cleats: contact us.
- Standard belt material: acetal low friction.
- Optional belt material: contact us.
- Standard belt color: brown.
- Straight conveyor belt widths: 3-¼”, 4-½”, 6”, 7-½”, 10”, 12”.
- Curved conveyor belt widths: 3-¼”, 4-½”, 7-½”, 10”, 12”.
- Conveyor length: minimum 36” long.
- Frame material: stainless steel 304, gage 12.
- Frame finish: polished to a #4 finish.
- Weld finish: continuous heli-arc welds, grounded and polished.
- Reducer: direct mount, vent free aluminum alloy housing.
- Bearings: two bolt flange bearings, permanently lubricated.
- Mechanical specifications are subject to change without prior notification.
Ordering information
- Part numbering legend: refer to page XCT 10.
- Motor package: refer to conveyor components section on page XCC 81.
- Optional control panel: refer to conveyor components section on page XCC 89.
- Guide rails: refer to conveyor components section on page XCC 92.
- Supports: refer to conveyor components section on page XCC 99.
- Custom application: contact factory for assistance.
Conveyor Body
|
Straight conveyor |
Belt width
|
X |
Length |
Curved conveyor |
XCT-S01-C-YYY-0325 |
3-1/4” |
3-31/32” |
YYY |
XCT-C01-C-YYY-0325 |
XCT-S01-C-YYY-0450 |
4-1/2” |
5-7/32” |
YYY |
XCT-C01-C-YYY-0450 |
XCT-S01-C-YYY-0600 |
6” |
6-23/32” |
YYY |
Not available |
XCT-S01-C-YYY-0750 |
7-1/2” |
8-7/32” |
YYY |
XCT-C01-C-YYY-0750 |
XCT-S01-C-YYY-1000 |
10” |
10-23/32” |
YYY |
XCT-C01-C-YYY-1000 |
XCT-S01-C-YYY-1200 |
12” |
12-23/32” |
YYY |
XCT-C01-C-YYY-1200 |
XCT-S01-C-YYY-BBBB |
BBBB |
|
YYY |
XCT-C01-C-YYY-BBBB |
|
|
|
|
|
Straight conveyor |
Belt width
|
X |
Length |
Curved conveyor |
XCT-S02-C-YYY-0325 |
3-1/4” |
3-31/32 |
YYY |
XCT-C02-C-YYY-0325 |
XCT-S02-C-YYY-0450 |
4-1/2” |
5-7/32” |
YYY |
XCT-C02-C-YYY-0450 |
XCT-S02-C-YYY-0600 |
6” |
6-23/32” |
YYY |
Not available |
XCT-S02-C-YYY-0750 |
7-1/2” |
8-7/32” |
YYY |
XCT-C02-C-YYY-0750 |
XCT-S02-C-YYY-1000 |
10” |
10-23/32” |
YYY |
XCT-C02-C-YYY-1000 |
XCT-S02-C-YYY-1200 |
12” |
12-23/32” |
YYY |
XCT-C02-C-YYY-1200 |
XCT-S02-C-YYY-BBBB |
BBBB |
|
YYY |
XCT-C02-C-YYY-BBBB |
|
|
|
|
|
Straight conveyor cross section
|
Curved conveyor cross section
|
Standard Profile
|
Low Profile
|
Standard Profile
|
Low Profile
|
X
|
Z
|
X
|
Z
|
X
|
Z
|
X
|
Z
|
3-1/4” |
3-1/2” |
3-1/4” |
3-1/2” |
3-1/4” |
3-1/2” |
3-1/4” |
3-1/2” |
4-1/2” |
6-1/4” |
4-1/2” |
3-1/2” |
4-1/2” |
6-1/4” |
4-1/2” |
3-1/2” |
6” |
6-1/4” |
6” |
3-1/2” |
6” |
6-1/4” |
6” |
3-1/2” |
7-1/2” |
6-1/4” |
7-1/2” |
3-1/2” |
7-1/2” |
6-1/4” |
7-1/2” |
3-1/2” |
10” |
6-1/4” |
10” |
3-1/2” |
10” |
6-1/4” |
10” |
3-1/2” |
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
Note: Maximum section length: 10’-0”. |
|
|
Idle Ends
Straight conveyor |
Belt width
|
X |
Curved conveyor |
XCT-S01-I-0325 |
3-1/4” |
3-31/32” |
XCT-C01-I-0325 |
XCT-S01-I-0450 |
4-1/2” |
5-7/32” |
XCT-C01-I-0450 |
XCT-S01-I-0600 |
6” |
6-23/32” |
Not available |
XCT-S01-I-0750 |
7-1/2” |
8-7/32” |
XCT-C01-I-0750 |
XCT-S01-I-1000 |
10” |
10-23/32” |
XCT-C01-I-1000 |
XCT-S01-I-1200 |
12” |
12-23/32” |
XCT-C01-I-1200 |
XCT-S01-I-BBBB |
BBBB |
|
XCT-C01-I-BBBB |
|
|
|
|
Note: For low profile conveyor selection refer to the part numbering legend on page XCT10.
Idle section length will be given by total conveyor length. |
 |
|
|
|
Drive unit – end drives
Left hand side |
|
|
|
Straight conveyor |
Belt width
|
X |
Curved conveyor |
XCT-S01-D-OEL-0325 |
3-1/4” |
3-31/32” |
XCT-C01-D-OEL-0325 |
XCT-S01-D-OEL-0450 |
4-1/2” |
5-7/32” |
XCT-C01-D-OEL-0450 |
XCT-S01-D-OEL-0600 |
6” |
6-23/32” |
Not available |
XCT-S01-D-OEL-0750 |
7-1/2” |
8-7/32” |
XCT-C01-D-OEL-0750 |
XCT-S01-D-OEL-1000 |
10” |
10-23/32” |
XCT-C01-D-OEL-1000 |
XCT-S01-D-OEL-1200 |
12” |
12-23/32” |
XCT-C01-D-OEL-1200 |
XCT-S01-D-OEL-BBBB |
BBBB |
|
XCT-C01-D-OEL-BBBB |
|
|
|
|
Note: For low profile conveyor and right hand selection refer to the part numbering legend on page XCT10.
Drive section length will be given by total conveyor length. |
|
 |
|
|
Drive unit – high capacity end drives
Left hand side |
|
|
|
Straight conveyor |
Belt width
|
X |
Curved conveyor |
XCT-S01-D-OHL-0325 |
3-1/4” |
3-31/32” |
XCT-C01-D-OHL-0325 |
XCT-S01-D-OHL-0450 |
4-1/2” |
5-7/32” |
XCT-C01-D-OHL-0450 |
XCT-S01-D-OHL-0600 |
6” |
6-23/32” |
Not available |
XCT-S01-D-OHL-0750 |
7-1/2” |
8-7/32” |
XCT-C01-D-OHL-0750 |
XCT-S01-D-OHL-1000 |
10” |
10-23/32” |
XCT-C01-D-OHL-1000 |
XCT-S01-D-OHL-1200 |
12” |
12-23/32” |
XCT-C01-D-OHL-1200 |
XCT-S01-D-OHL-BBBB |
BBBB |
|
XCT-C01-D-OHL-BBBB |
|
|
|
|
Note: For low profile conveyor and right hand selection refer to the part numbering legend on page XCT10. |
|
 |
|
|
Drive unit – center drives
Left hand side |
|
|
|
Straight conveyor |
Belt width
|
X |
Curved conveyor |
XCT-S01-D-OCL-0325 |
3-1/4” |
3-31/32” |
XCT-C01-D-OCL-0325 |
XCT-S01-D-OCL-0450 |
4-1/2” |
5-7/32” |
XCT-C01-D-OCL-0450 |
XCT-S01-D-OCL-0600 |
6” |
6-23/32” |
Not available |
XCT-S01-D-OCL-0750 |
7-1/2” |
8-7/32” |
XCT-C01-D-OCL-0750 |
XCT-S01-D-OCL-1000 |
10” |
10-23/32” |
XCT-C01-D-OCL-1000 |
XCT-S01-D-OCL-1200 |
12” |
12-23/32” |
XCT-C01-D-OCL-1200 |
XCT-S01-D-OCL-BBBB |
BBBB |
|
XCT-C01-D-OCL-BBBB |
|
|
|
|
Note: For low profile conveyor and right hand selection refer to the part numbering legend on page XCT10. |
|
 |
|
|
Drive end – offset transfer
Left hand side |
|
|
|
|
Straight conveyor |
Belt width
|
X |
A |
Curved conveyor |
XCT-S01-D-OOL-0325 |
3-1/4” |
3-31/32” |
7-5/16” |
XCT-C01-D-OOL-0325 |
XCT-S01-D-OOL-0450 |
4-1/2” |
5-7/32” |
9-27/32” |
XCT-C01-D-OOL-0450 |
XCT-S01-D-OOL-0600 |
6” |
6-23/32” |
12-13/16” |
Not available |
XCT-S01-D-OOL-0750 |
7-1/2” |
8-7/32” |
15-13/16” |
XCT-C01-D-OOL-0750 |
XCT-S01-D-OOL-1000 |
10” |
10-23/32” |
20-13/16” |
XCT-C01-D-OOL-1000 |
XCT-S01-D-OOL-1200 |
12” |
12-23/32” |
24-13/16” |
XCT-C01-D-OOL-1200 |
XCT-S01-D-OOL-BBBB |
BBBB |
|
|
XCT-C01-D-OOL-BBBB |
|
|
|
|
|
Note: For low profile conveyor and right hand selection refer to the part numbering legend on page XCT10.
Consult factory for narrower gap distance. |
|
 |
|
|
Drive end – in line transfer
Left hand side |
|
|
|
|
Straight conveyor |
Belt width
|
X |
A |
Y |
XCT-C01-D-OIL-0325 |
3-1/4” |
3-3/8” |
7-5/16” |
71-11/16” |
XCT-C01-D-OIL-0450 |
4-1/2” |
4-5/8” |
9-27/32” |
75-9/16” |
XCT-C01-D-OIL-0750 |
7-1/2” |
7-5/8” |
15-13/16” |
79-31/32” |
XCT-C01-D-OIL-1000 |
10” |
10-1/8” |
20-13/16” |
83-1/2” |
XCT-C01-D-OIL-1200 |
12” |
12-1/8” |
24-13/16” |
85-7/8” |
XCT-C01-D-OIL-BBBB |
BBBB |
|
|
|
|
|
|
|
|
Note: For low profile conveyor and right hand selection refer to the part numbering legend on page XCT10.
Available only for curved conveyor. Consult factory for narrower gap distance. |
|
 |
|
|
|
Bends – horizontal bends
|
30° Horizontal bends |
 |
Curved conveyor |
Belt Width
|
X |
R |
XCT-C01-B-030-0325 |
3-1/4” |
3-31/32” |
18” |
XCT-C01-B-030-0450 |
4-1/2” |
5-7/32” |
24” |
XCT-C01-B-030-0750 |
7-1/2” |
8-7/32” |
24” |
XCT-C01-B-030-1000 |
10” |
10-23/32” |
24” |
XCT-C01-B-030-1200 |
12” |
12-23/32” |
24” |
XCT-C01-B-030-BBBB |
BBBB |
|
|
Note: Available only for curved conveyor.
For low profile replace “C01” with “C02”. |
|
45° Horizontal bends |
 |
Curved conveyor |
Belt Width
|
X |
R |
XCT-C01-B-045-0325 |
3-1/4” |
3-31/32” |
18” |
XCT-C01-B-045-0450 |
4-1/2” |
5-7/32” |
24” |
XCT-C01-B-045-0750 |
7-1/2” |
8-7/32” |
24” |
XCT-C01-B-045-1000 |
10” |
10-23/32” |
24” |
XCT-C01-B-045-1200 |
12” |
12-23/32” |
24” |
XCT-C01-B-045-BBBB |
BBBB |
|
|
Note: Available only for curved conveyor.
For low profile replace “C01” with “C02”. |
|
90° Horizontal bends |
 |
Curved conveyor |
Belt Width
|
X |
R |
XCT-C01-B-090-0325 |
3-1/4” |
3-31/32” |
18” |
XCT-C01-B-090-0450 |
4-1/2” |
5-7/32” |
24” |
XCT-C01-B-090-0750 |
7-1/2” |
8-7/32” |
24” |
XCT-C01-B-090-1000 |
10” |
10-23/32” |
24” |
XCT-C01-B-090-1200 |
12” |
12-23/32” |
24” |
XCT-C01-B-090-BBBB |
BBBB |
|
|
Note: Available only for curved conveyor.
For low profile replace “C01” with “C02”. |
|
|
|